Baby Rule #1 - What goes in, must come out.
And when it comes out, it ends up in our cloth diapers. Because we wash our diapers, and don't want to overload our washer with poop, it has become necessary on occasion to rinse the "output" into the toilet. Enter, diaper sprayer.
A diaper sprayer is just a sink sprayer attached to the incoming water line of your toilet. I did some research on the internet and found that to buy a pre-made diaper sprayer from a company would cost $40+. Being on a budget, and having the desire to learn more handyman type work, I decided to make one myself. All the parts I used together cost a little under $30.
I went to Lowe's, and wandered around until I found the plumbing section. After a few minutes of staring blankly at all the parts and pieces, I was asked by a friendly and helpful Lowe's associate, "Can I help you?" Not wanting to get into a discussion about spraying poop, I just informed him that I wanted to install a sink sprayer onto a water line that did not already have one. He took me to the sink sprayers, and showed me the options. I said again that I wanted to install one on a water line that did not already have a sprayer (the sprayers in those packs are just to replace sprayers that are broken). After a few minutes of useless conversation, I thanked him for his time and walked around the isle to get him off my tail. Deciding to figure it out for myself. An hour or so later, I left Lowe's empty handed, having found that they did not have the parts I needed.
Here's the situation. The standard water input line to a toilet (or a sink for that matter) has a 3/8" shutoff valve, then a 3/8" tube or pipe that runs to the toilet. However, there is not just one sort of measurement for pipe threads. The standard shutoff valve for the toilet is 3/8" compression thread, marked on adapters and such as "OD" for "outer diameter." Sink sprayers use a 1/4" iron pipe thread, specifically they end in a female iron pipe thread, or "FIP." So, the difficulty is finding the right pieces to connect a 3/8" OD to a 1/4" FIP. Lowe's (at least the one in Muncie) doesn't have these pieces, but Home Depot did, and these are the pieces I used. (Click any image to see an enlarged version)
Top: This piece is 1/4" MIP (male iron pipe) on one end, to connect to the sprayer, and 1/4" OD on the other end, to connect to the hose I'll use.
Middle: This piece is a shutoff valve, 1/4" OD on both ends. It is important to include a shutoff valve in your line, because a sink sprayer is not designed to handle constant pressure. Make sure to shut off the water supply to your diaper sprayer when you're not using it.
Bottom: T-splice. This piece goes in between the 3/8" OD shutoff valve and the water line to your toilet, adding a 1/4" OD output that you connect the new hose to.
Left: Two icemaker supply line cables, 1/4" ID (female compression threads). I guess they don't make adapters with female compression thread on both ends, which is what I need to connect the T-splice to the shutoff valve I'm adding, and the shutoff valve to the adapter which connects to the sprayer. So, I used two icemaker supply cables.
Right: Sink sprayer. I opted to get a pretty good one, you could save a few bucks by using a slightly lower quality one and still get good use out of it.
A wrench. You need to make sure all your connections are tight, but do not over tighten. Tightening them past the point where the threads stop can ruin your threads.
Once you have all the pieces you need, turn off the shutoff valve from the toilet's water supply line, and disconnect the tube to the toilet (have a bowl ready, the water in the line might run out when you disconnect it). EDIT: My wife reminded me that some people suggest flushing the toilet after turning off the water supply to get the water out of the top of the toilet. I haven't found this to be necessary, but it won't hurt.
Connect all the pieces together as shown. The sprayer connects to the larger end of the A-23 adapter, the smaller end of the adapter connects into one of the icemaker hoses. The shutoff valve connects the two icemaker hoses, and the last hose hooks onto the smaller end of the T-splice.
After you've got the pieces hooked up together, you can attach the T-splice to the shutoff valve you opened up, and put the supply to the toilet back on the top of the splice. Make sure these connections are tight.
After connecting everything, turn the main water supply back on, and let the toilet fill up before you try to use it again. Turn off the shutoff valve you added to the line whenever you're not using the sprayer, remember it's not made to handle that pressure, but you can keep the main shutoff valve open all the time just like normal. Here's what it looks like in action:
Part of being a man is being able to make a good diaper sprayer.
grace and peace,
J